U-Boot SPL 2021.10 (Jan 19 2023 - 04:09:41 +0800) DDR version: dc2e84f0. Trying to boot from SPI OpenSBI v1.2 ____ _____ ____ _____ / __ \ / ____| _ \_ _| | | | |_ __ ___ _ __ | (___ | |_) || | | | | | '_ \ / _ \ '_ \ \___ \| _ < | | | |__| | |_) | __/ | | |____) | |_) || |_ \____/| .__/ \___|_| |_|_____/|____/_____| | | |_| Platform Name : StarFive VisionFive V2 Platform Features : medeleg Platform HART Count : 5 Platform IPI Device : aclint-mswi Platform Timer Device : aclint-mtimer @ 4000000Hz Platform Console Device : uart8250 Platform HSM Device : jh7110-hsm Platform PMU Device : --- Platform Reboot Device : pm-reset Platform Shutdown Device : pm-reset Firmware Base : 0x40000000 Firmware Size : 288 KB Runtime SBI Version : 1.0 Domain0 Name : root Domain0 Boot HART : 1 Domain0 HARTs : 0*,1*,2*,3*,4* Domain0 Region00 : 0x0000000002000000-0x000000000200ffff (I) Domain0 Region01 : 0x0000000040000000-0x000000004007ffff () Domain0 Region02 : 0x0000000000000000-0xffffffffffffffff (R,W,X) Domain0 Next Address : 0x0000000040200000 Domain0 Next Arg1 : 0x0000000042200000 Domain0 Next Mode : S-mode Domain0 SysReset : yes Boot HART ID : 1 Boot HART Domain : root Boot HART Priv Version : v1.11 Boot HART Base ISA : rv64imafdcbx Boot HART ISA Extensions : none Boot HART PMP Count : 8 Boot HART PMP Granularity : 4096 Boot HART PMP Address Bits: 34 Boot HART MHPM Count : 2 Boot HART MIDELEG : 0x0000000000000222 Boot HART MEDELEG : 0x000000000000b109 U-Boot 2021.10 (Jan 19 2023 - 04:09:41 +0800), Build: jenkins-github_visionfive2-6 CPU: rv64imacu Model: StarFive VisionFive V2 DRAM: 8 GiB MMC: sdio0@16010000: 0, sdio1@16020000: 1 Loading Environment from SPIFlash... SF: Detected gd25lq128 with page size 256 Bytes, erase size 4 KiB, total 16 MiB *** Warning - bad CRC, using default environment StarFive EEPROM format v2 --------EEPROM INFO-------- Vendor : PINE64 Product full SN: STAR64V1-2310-D008E000-00000006 data version: 0x2 PCB revision: 0xc1 BOM revision: A Ethernet MAC0 address: 6c:cf:39:00:75:63 Ethernet MAC1 address: 6c:cf:39:00:75:64 --------EEPROM INFO-------- In: serial@10000000 Out: serial@10000000 Err: serial@10000000 Model: StarFive VisionFive V2 Net: eth0: ethernet@16030000, eth1: ethernet@16040000 switch to partitions #0, OK mmc1 is current device found device 1 bootmode flash device 1 ** Invalid partition 3 ** Couldn't find partition mmc 1:3 Can't set block device ** Invalid partition 3 ** Couldn't find partition mmc 1:3 Can't set block device Hit any key to stop autoboot: 2 1 0 ** Invalid partition 3 ** Couldn't find partition mmc 1:3 Can't set block device Importing environment from mmc1 ... ## Warning: Input data exceeds 1048576 bytes - truncated ## Info: input data size = 1048578 = 0x100002 ** Invalid partition 2 ** Couldn't find partition mmc 1:2 Can't set block device ## Warning: defaulting to text format ## Error: "boot2" not defined switch to partitions #0, OK mmc1 is current device Scanning mmc 1:1... Found /boot/extlinux/extlinux.conf Retrieving file: /boot/extlinux/extlinux.conf 344 bytes read in 5 ms (66.4 KiB/s) 1: Armbian Retrieving file: /boot/uInitrd 10783262 bytes read in 478 ms (21.5 MiB/s) Retrieving file: /boot/Image 26410944 bytes read in 1254 ms (20.1 MiB/s) append: root=UUID=821ef80c-754b-4e7c-8dce-a258b31eff0d console=ttyS0,115200n8 console=tty0 earlycon=sbi rootflags=data=writeback stmmaceth=chain_mode:1 rw rw no_console_suspend consoleblank=0 fsck.fix=yes fsck.repair=yes net.ifnames=0 Retrieving file: /boot/dtb/starfive/jh7110-pine64-star64.dtb 47245 bytes read in 11 ms (4.1 MiB/s) ## Loading init Ramdisk from Legacy Image at 46100000 ... Image Name: uInitrd Image Type: RISC-V Linux RAMDisk Image (gzip compressed) Data Size: 10783198 Bytes = 10.3 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 46000000 Booting using the fdt blob at 0x46000000 Using Device Tree in place at 0000000046000000, end 000000004600e88c Starting kernel ... clk u5_dw_i2c_clk_core already disabled clk u5_dw_i2c_clk_apb already disabled [ 0.000000] Linux version 5.15.107-15659-g7943fd6427b0-dirty (schaecsn@g510) (riscv64-linux-gnu-gcc (Debian 12.2.0-13) 12.2.0, GNU ld (GNU Binutils for Debian) 2.40) #1 SMP Sun May 28 22:22:26 PDT 2023 [ 0.000000] OF: fdt: Ignoring memory range 0x40000000 - 0x40200000 [ 0.000000] Machine model: Pine64 Star64 [ 0.000000] earlycon: sbi0 at I/O port 0x0 (options '') [ 0.000000] printk: bootconsole [sbi0] enabled [ 0.000000] cma: Reserved 16 MiB at 0x00000000bf000000 [ 0.000000] Reserved memory: created CMA memory pool at 0x0000000080000000, size 512 MiB [ 0.000000] OF: reserved mem: initialized node linux,cma, compatible id shared-dma-pool [ 0.000000] Zone ranges: [ 0.000000] DMA32 [mem 0x0000000040200000-0x00000000ffffffff] [ 0.000000] Normal [mem 0x0000000100000000-0x000000023fffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000040200000-0x00000000c010ffff] [ 0.000000] node 0: [mem 0x00000000c0110000-0x00000000c01fffff] [ 0.000000] node 0: [mem 0x00000000c0200000-0x000000023fffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000040200000-0x000000023fffffff] [ 0.000000] SBI specification v1.0 detected [ 0.000000] SBI implementation ID=0x1 Version=0x10002 [ 0.000000] SBI TIME extension detected [ 0.000000] SBI IPI extension detected [ 0.000000] SBI RFENCE extension detected [ 0.000000] SBI SRST extension detected [ 0.000000] SBI v0.2 HSM extension detected [ 0.000000] CPU with hartid=0 is not available [ 0.000000] CPU with hartid=0 is not available [ 0.000000] riscv: base ISA extensions acdfim [ 0.000000] riscv: ELF capabilities acdfim [ 0.000000] percpu: Embedded 18 pages/cpu s34088 r8192 d31448 u73728 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 2067975 [ 0.000000] Kernel command line: root=UUID=821ef80c-754b-4e7c-8dce-a258b31eff0d console=ttyS0,115200n8 console=tty0 earlycon=sbi rootflags=data=writeback stmmaceth=chain_mode:1 rw rw no_console_suspend consoleblank=0 fsck.fix=yes fsck.repair=yes net.ifnames=0 [ 0.000000] Dentry cache hash table entries: 1048576 (order: 11, 8388608 bytes, linear) [ 0.000000] Inode-cache hash table entries: 524288 (order: 10, 4194304 bytes, linear) [ 0.000000] mem auto-init: stack:all(zero), heap alloc:off, heap free:off [ 0.000000] software IO TLB: mapped [mem 0x00000000fb000000-0x00000000ff000000] (64MB) [ 0.000000] Memory: 7548316K/8386560K available (11076K kernel code, 7217K rwdata, 4096K rodata, 2189K init, 405K bss, 297572K reserved, 540672K cma-reserved) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 [ 0.000000] rcu: Hierarchical RCU implementation. [ 0.000000] rcu: CRCU restricting CPUs from NR_CPUS=8 to nr_cpu_ids=4. [ 0.000000] rcu: CRCU debug extended QS entry/exit. [ 0.000000] Tracing variant of Tasks RCU enabled. [ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. [ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4 [ 0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0 [ 0.000000] CPU with hartid=0 is not available [ 0.000000] riscv-intc: unable to find hart id for /cpus/cpu@0/interrupt-controller [ 0.000000] riscv-intc: 64 local interrupts mapped [ 0.000000] plic: plic@c000000: mapped 136 interrupts with 4 handlers for 9 contexts. [ 0.000000] riscv_timer_init_dt: Registering clocksource cpuid [0] hartid [1] [ 0.000000] clocksource: riscv_clocksource: mask: 0xffffffffffffffff max_cycles: 0x1d854df40, max_idle_ns: 881590404240 ns [ 0.000001] sched_clock: 64 bits at 4MHz, resolution 250ns, wraps every 2199023255500ns [ 0.008240] clocksource: timer@13050000.ch0: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 79635851949 ns [ 0.018441] clocksource: timer@13050000.ch1: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 79635851949 ns [ 0.028755] clocksource: timer@13050000.ch2: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 79635851949 ns [ 0.039069] clocksource: timer@13050000.ch3: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 79635851949 ns [ 0.049648] Console: colour dummy device 80x25 [ 0.054007] printk: console [tty0] enabled [ 0.058164] printk: bootconsole [sbi0] disabled [ 0.000000] Linux version 5.15.107-15659-g7943fd6427b0-dirty (schaecsn@g510) (riscv64-linux-gnu-gcc (Debian 12.2.0-13) 12.2.0, GNU ld (GNU Binutils for Debian) 2.40) #1 SMP Sun May 28 22:22:26 PDT 2023 [ 0.000000] OF: fdt: Ignoring memory range 0x40000000 - 0x40200000 [ 0.000000] Machine model: Pine64 Star64 [ 0.000000] earlycon: sbi0 at I/O port 0x0 (options '') [ 0.000000] printk: bootconsole [sbi0] enabled [ 0.000000] cma: Reserved 16 MiB at 0x00000000bf000000 [ 0.000000] Reserved memory: created CMA memory pool at 0x0000000080000000, size 512 MiB [ 0.000000] OF: reserved mem: initialized node linux,cma, compatible id shared-dma-pool [ 0.000000] Zone ranges: [ 0.000000] DMA32 [mem 0x0000000040200000-0x00000000ffffffff] [ 0.000000] Normal [mem 0x0000000100000000-0x000000023fffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000040200000-0x00000000c010ffff] [ 0.000000] node 0: [mem 0x00000000c0110000-0x00000000c01fffff] [ 0.000000] node 0: [mem 0x00000000c0200000-0x000000023fffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000040200000-0x000000023fffffff] [ 0.000000] SBI specification v1.0 detected [ 0.000000] SBI implementation ID=0x1 Version=0x10002 [ 0.000000] SBI TIME extension detected [ 0.000000] SBI IPI extension detected [ 0.000000] SBI RFENCE extension detected [ 0.000000] SBI SRST extension detected [ 0.000000] SBI v0.2 HSM extension detected [ 0.000000] CPU with hartid=0 is not available [ 0.000000] CPU with hartid=0 is not available [ 0.000000] riscv: base ISA extensions acdfim [ 0.000000] riscv: ELF capabilities acdfim [ 0.000000] percpu: Embedded 18 pages/cpu s34088 r8192 d31448 u73728 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 2067975 [ 0.000000] Kernel command line: root=UUID=821ef80c-754b-4e7c-8dce-a258b31eff0d console=ttyS0,115200n8 console=tty0 earlycon=sbi rootflags=data=writeback stmmaceth=chain_mode:1 rw rw no_console_suspend consoleblank=0 fsck.fix=yes fsck.repair=yes net.ifnames=0 [ 0.000000] Dentry cache hash table entries: 1048576 (order: 11, 8388608 bytes, linear) [ 0.000000] Inode-cache hash table entries: 524288 (order: 10, 4194304 bytes, linear) [ 0.000000] mem auto-init: stack:all(zero), heap alloc:off, heap free:off [ 0.000000] software IO TLB: mapped [mem 0x00000000fb000000-0x00000000ff000000] (64MB) [ 0.000000] Memory: 7548316K/8386560K available (11076K kernel code, 7217K rwdata, 4096K rodata, 2189K init, 405K bss, 297572K reserved, 540672K cma-reserved) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 [ 0.000000] rcu: Hierarchical RCU implementation. [ 0.000000] rcu: CRCU restricting CPUs from NR_CPUS=8 to nr_cpu_ids=4. [ 0.000000] rcu: CRCU debug extended QS entry/exit. [ 0.000000] Tracing variant of Tasks RCU enabled. [ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. [ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4 [ 0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0 [ 0.000000] CPU with hartid=0 is not available [ 0.000000] riscv-intc: unable to find hart id for /cpus/cpu@0/interrupt-controller [ 0.000000] riscv-intc: 64 local interrupts mapped [ 0.000000] plic: plic@c000000: mapped 136 interrupts with 4 handlers for 9 contexts. [ 0.000000] riscv_timer_init_dt: Registering clocksource cpuid [0] hartid [1] [ 0.000000] clocksource: riscv_clocksource: mask: 0xffffffffffffffff max_cycles: 0x1d854df40, max_idle_ns: 881590404240 ns [ 0.000001] sched_clock: 64 bits at 4MHz, resolution 250ns, wraps every 2199023255500ns [ 0.008240] clocksource: timer@13050000.ch0: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 79635851949 ns [ 0.018441] clocksource: timer@13050000.ch1: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 79635851949 ns [ 0.028755] clocksource: timer@13050000.ch2: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 79635851949 ns [ 0.039069] clocksource: timer@13050000.ch3: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 79635851949 ns [ 0.049648] Console: colour dummy device 80x25 [ 0.054007] printk: console [tty0] enabled [ 0.058164] printk: bootconsole [sbi0] disabled [ 0.062806] Calibrating delay loop (skipped), value calculated using timer frequency.. 8.00 BogoMIPS (lpj=40000) [ 0.062831] pid_max: default: 32768 minimum: 301 [ 0.063173] Mount-cache hash table entries: 16384 (order: 5, 131072 bytes, linear) [ 0.063353] Mountpoint-cache hash table entries: 16384 (order: 5, 131072 bytes, linear) [ 0.065185] ASID allocator disabled [ 0.065316] rcu: Hierarchical SRCU implementation. [ 0.066354] smp: Bringing up secondary CPUs ... [ 0.068341] smp: Brought up 1 node, 4 CPUs [ 0.070300] devtmpfs: initialized [ 0.078120] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.078155] futex hash table entries: 1024 (order: 4, 65536 bytes, linear) [ 0.092058] pinctrl core: initialized pinctrl subsystem [ 0.093457] NET: Registered PF_NETLINK/PF_ROUTE protocol family [ 0.094220] thermal_sys: Registered thermal governor 'step_wise' [ 0.094555] cpuidle: using governor menu [ 0.116840] platform soc:dsi-output: Fixing up cyclic dependency with 29400000.dc8200 [ 0.117358] platform 295d0000.mipi: Fixing up cyclic dependency with soc:dsi-output [ 0.117796] platform 29590000.hdmi: Fixing up cyclic dependency with 29400000.dc8200 [ 0.156345] HugeTLB registered 1.00 GiB page size, pre-allocated 0 pages [ 0.156374] HugeTLB registered 2.00 MiB page size, pre-allocated 0 pages [ 0.160392] vgaarb: loaded [ 0.160658] SCSI subsystem initialized [ 0.160867] usbcore: registered new interface driver usbfs [ 0.160917] usbcore: registered new interface driver hub [ 0.160967] usbcore: registered new device driver usb [ 0.161312] mc: Linux media interface: v0.10 [ 0.161352] videodev: Linux video capture interface: v2.00 [ 0.161615] Advanced Linux Sound Architecture Driver Initialized. [ 0.162663] clocksource: Switched to clocksource riscv_clocksource [ 0.169982] NET: Registered PF_INET protocol family [ 0.171275] IP idents hash table entries: 131072 (order: 8, 1048576 bytes, linear) [ 0.178997] tcp_listen_portaddr_hash hash table entries: 4096 (order: 5, 163840 bytes, linear) [ 0.179249] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear) [ 0.179295] TCP established hash table entries: 65536 (order: 7, 524288 bytes, linear) [ 0.180138] TCP bind hash table entries: 65536 (order: 9, 2097152 bytes, linear) [ 0.182117] TCP: Hash tables configured (established 65536 bind 65536) [ 0.182424] UDP hash table entries: 4096 (order: 6, 393216 bytes, linear) [ 0.183005] UDP-Lite hash table entries: 4096 (order: 6, 393216 bytes, linear) [ 0.183656] NET: Registered PF_UNIX/PF_LOCAL protocol family [ 0.184459] RPC: Registered named UNIX socket transport module. [ 0.184483] RPC: Registered udp transport module. [ 0.184497] RPC: Registered tcp transport module. [ 0.184511] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.185278] PCI: CLS 0 bytes, default 64 [ 0.186354] Initialise system trusted keyrings [ 0.186594] Unpacking initramfs... [ 0.203141] workingset: timestamp_bits=62 max_order=21 bucket_order=0 [ 0.209665] NFS: Registering the id_resolver key type [ 0.209723] Key type id_resolver registered [ 0.209740] Key type id_legacy registered [ 0.209831] nfs4filelayout_init: NFSv4 File Layout Driver Registering... [ 0.209853] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering... [ 0.209897] ntfs: driver 2.1.32 [Flags: R/W]. [ 0.210119] jffs2: version 2.2. (NAND) © 2001-2006 Red Hat, Inc. [ 0.210499] fuse: init (API version 7.34) [ 0.249737] NET: Registered PF_ALG protocol family [ 0.249794] Key type asymmetric registered [ 0.249812] Asymmetric key parser 'x509' registered [ 0.249925] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 249) [ 0.249952] io scheduler mq-deadline registered [ 0.249968] io scheduler kyber registered [ 0.352617] clk-starfive-jh7110 13020000.clock-controller: starfive JH7110 clkgen init successfully. [ 0.353934] L2CACHE: DataError @ 0x00000000.08040140 [ 0.354009] L2CACHE: DataFail @ 0x00000000.08040074 [ 0.354094] L2CACHE: No. of Banks in the cache: 8 [ 0.354116] L2CACHE: No. of ways per bank: 16 [ 0.354134] L2CACHE: Sets per bank: 256 [ 0.354151] L2CACHE: Bytes per cache block: 64 [ 0.354169] L2CACHE: Index of the largest way enabled: 15 [ 0.354441] jh7110-pmu 17030000.power-controller: registered 8 power domains [ 0.418729] Serial: 8250/16550 driver, 6 ports, IRQ sharing disabled [ 0.422518] @@#########################@@ [ 0.428598] @@ dev ptr:ffffffe0bff3ac00/1500/1 [ 0.428879] PVR_K: 1: Read BVNC 36.50.54.182 from HW device registers [ 0.428956] PVR_K: 1: RGX Device registered BVNC 36.50.54.182 with 1 core in the system [ 0.697599] Freeing initrd memory: 10524K [ 0.697853] pvrsrvkm 18000000.gpu: Direct firmware load for rgx.fw.36.50.54.182 failed with error -2 [ 0.697983] pvrsrvkm 18000000.gpu: Direct firmware load for rgx.fw.36.50p.54.182 failed with error -2 [ 0.698091] pvrsrvkm 18000000.gpu: Direct firmware load for rgx.fw failed with error -2 [ 0.698133] PVR_K:(Fatal): 1: All RGX Firmware image loads failed for 'rgx.fw.36.50.54.182' (PVRSRV_ERROR_NOT_FOUND) [1599] [ 0.698170] PVR_K:(Error): 1: RGXInit: InitFirmware failed (275) [1556] [ 0.698198] PVR_K:(Error): 1: RGXInit() failed (PVRSRV_ERROR_NOT_FOUND) in PVRSRVCommonDeviceInitialise() [2156] [ 0.698232] PVR_K:(Error): 1: PVRSRVDeviceFinalise() failed (PVRSRV_ERROR_NOT_INITIALISED) in PVRSRVCommonDeviceInitialise() [2170] [ 0.698271] [drm:pvr_drm_load] *ERROR* device (____ptrval____) initialisation failed (err=-19) [ 0.708412] loop: module loaded [ 0.710932] spi-nor spi0.0: gd25lq128d (16384 Kbytes) [ 0.728927] 3 fixed-partitions partitions found on MTD device 13010000.spi.0 [ 0.728969] Creating 3 MTD partitions on "13010000.spi.0": [ 0.728995] 0x000000000000-0x000000040000 : "spl" [ 0.730670] 0x000000100000-0x000000400000 : "uboot" [ 0.732218] 0x000000f00000-0x000001000000 : "data" [ 0.736045] CAN device driver interface [ 0.737052] starfive-eth-plat 16030000.ethernet: User ID: 0x41, Synopsys ID: 0x52 [ 0.737096] starfive-eth-plat 16030000.ethernet: CDWMAC4/5 [ 0.737120] starfive-eth-plat 16030000.ethernet: DMA HW capability register supported [ 0.737149] starfive-eth-plat 16030000.ethernet: RX Checksum Offload Engine supported [ 0.737178] starfive-eth-plat 16030000.ethernet: Wake-Up On Lan supported [ 0.737268] starfive-eth-plat 16030000.ethernet: TSO supported [ 0.737292] starfive-eth-plat 16030000.ethernet: Enable RX Mitigation via HW Watchdog Timer [ 0.737324] starfive-eth-plat 16030000.ethernet: Enabled L3L4 Flow TC (entries=1) [ 0.737355] starfive-eth-plat 16030000.ethernet: Enabled RFS Flow TC (entries=8) [ 0.737385] starfive-eth-plat 16030000.ethernet: TSO feature enabled [ 0.737408] starfive-eth-plat 16030000.ethernet: Using 40 bits DMA width [ 0.988871] YT8531 Gigabit Ethernet stmmac-0:00: attached PHY driver (mii_bus:phy_addr=stmmac-0:00, irq=POLL) [ 0.988925] YT8531 Gigabit Ethernet stmmac-0:01: attached PHY driver (mii_bus:phy_addr=stmmac-0:01, irq=POLL) [ 0.990617] starfive-eth-plat 16040000.ethernet: User ID: 0x41, Synopsys ID: 0x52 [ 0.990660] starfive-eth-plat 16040000.ethernet: CDWMAC4/5 [ 0.990684] starfive-eth-plat 16040000.ethernet: DMA HW capability register supported [ 0.990714] starfive-eth-plat 16040000.ethernet: RX Checksum Offload Engine supported [ 0.990742] starfive-eth-plat 16040000.ethernet: Wake-Up On Lan supported [ 0.990838] starfive-eth-plat 16040000.ethernet: TSO supported [ 0.990863] starfive-eth-plat 16040000.ethernet: Enable RX Mitigation via HW Watchdog Timer [ 0.990894] starfive-eth-plat 16040000.ethernet: Enabled L3L4 Flow TC (entries=1) [ 0.990925] starfive-eth-plat 16040000.ethernet: Enabled RFS Flow TC (entries=8) [ 0.990955] starfive-eth-plat 16040000.ethernet: TSO feature enabled [ 0.990978] starfive-eth-plat 16040000.ethernet: Using 40 bits DMA width [ 1.241847] YT8531 Gigabit Ethernet stmmac-1:00: attached PHY driver (mii_bus:phy_addr=stmmac-1:00, irq=POLL) [ 1.241902] YT8531 Gigabit Ethernet stmmac-1:01: attached PHY driver (mii_bus:phy_addr=stmmac-1:01, irq=POLL) [ 1.244036] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 1.244078] ehci-pci: EHCI PCI platform driver [ 1.244152] ehci-platform: EHCI generic platform driver [ 1.244914] usbcore: registered new interface driver cdc_acm [ 1.244939] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters [ 1.245002] usbcore: registered new interface driver cdc_wdm [ 1.263120] starfive-rtc 17040000.rtc: registered as rtc0 [ 1.263303] i2c_dev: i2c /dev entries driver [ 1.263586] usbcore: registered new interface driver uvcvideo [ 1.282692] thermal thermal_zone0: failed to read out thermal zone (-110) [ 1.283048] starfive-wdt 13070000.wdog: Heartbeat: timeout=15, count/2=180000000 (0aba9500) [ 1.284336] sdhci: Secure Digital Host Controller Interface driver [ 1.284361] sdhci: Copyright(c) Pierre Ossman [ 1.284418] Synopsys Designware Multimedia Card Interface Driver [ 1.284773] sdhci-pltfm: SDHCI platform and OF driver helper [ 1.285332] ledtrig-cpu: registered to indicate activity on CPUs [ 1.285868] jh7110-sec 16000000.crypto: Unable to request sec_m dma channel in DMA channel [ 1.285903] jh7110-sec 16000000.crypto: Cannot initial dma chan [ 1.286216] usbcore: registered new interface driver usbhid [ 1.286241] usbhid: USB HID core driver [ 1.286350] usbcore: registered new interface driver rtl8852bu [ 1.286586] riscv-pmu-sbi: SBI PMU extension is available [ 1.286632] riscv-pmu-sbi: 16 firmware and 4 hardware counters [ 1.286654] riscv-pmu-sbi: Perf sampling/filtering is not supported as sscof extension is not available [ 1.287042] usbcore: registered new interface driver snd-usb-audio [ 1.289211] NET: Registered PF_INET6 protocol family [ 1.290585] Segment Routing with IPv6 [ 1.290669] In-situ OAM (IOAM) with IPv6 [ 1.290764] NET: Registered PF_PACKET protocol family [ 1.290795] can: controller area network core [ 1.290898] NET: Registered PF_CAN protocol family [ 1.290924] can: raw protocol [ 1.290945] can: broadcast manager protocol [ 1.290971] can: netlink gateway - max_hops=1 [ 1.291462] 9pnet: Installing 9P2000 support [ 1.291593] Key type dns_resolver registered [ 1.292578] Loading compiled-in X.509 certificates [ 1.329293] starfive_jh7110-pinctrl 13040000.gpio: SiFive GPIO chip registered 64 GPIOs [ 1.330156] starfive_jh7110-pinctrl 17020000.gpio: SiFive GPIO chip registered 4 GPIOs [ 1.330408] pl08xdmac 16008000.sec_dma: initialized 8 virtual memcpy channels [ 1.330460] pl08xdmac 16008000.sec_dma: initialized 16 virtual slave channels [ 1.332290] debugfs: Directory '16008000.sec_dma' with parent 'dmaengine' already present! [ 1.332340] pl08xdmac 16008000.sec_dma: DMA: PL080 rev0 at 0x16008000 irq 23 [ 1.332634] ssp-pl022 10060000.spi: ARM PL022 driver for StarFive SoC platform, device ID: 0x00041022 [ 1.332723] ssp-pl022 10060000.spi: mapped registers from 0x0000000010060000 to (____ptrval____) [ 1.333179] ssp-pl022 10060000.spi: Requested frequency: 10000000 Hz is unsupported,select by default 8250000 Hz [ 1.333601] ssp-pl022 10060000.spi: will use autosuspend for runtime pm, delay 100ms [ 1.337463] rtc-hym8563 2-0051: no valid clock/calendar values available [ 1.337645] rtc-hym8563 2-0051: registered as rtc1 [ 1.338630] rtc-hym8563 2-0051: no valid clock/calendar values available [ 1.338657] rtc-hym8563 2-0051: hctosys: unable to read the hardware clock [ 1.340768] at24 5-0050: supply vcc not found, using dummy regulator [ 1.341619] at24 5-0050: 512 byte 24c04 EEPROM, writable, 16 bytes/write [ 1.344013] axp15060-regulator 5-0036: Register mipi_0p9 done! vol range:900 ~ 900 mV [ 1.345943] axp15060-regulator 5-0036: Register hdmi_1p8 done! vol range:1800 ~ 1800 mV [ 1.347868] axp15060-regulator 5-0036: Register hdmi_0p9 done! vol range:900 ~ 900 mV [ 1.350241] axp15060-regulator 5-0036: Register cpu_vdd done! vol range:500 ~ 1540 mV [ 1.353654] pcie_plda 2c000000.pcie: host bridge /soc/pcie@2C000000 ranges: [ 1.353727] pcie_plda 2c000000.pcie: MEM 0x0038000000..0x003fffffff -> 0x0038000000 [ 1.353774] pcie_plda 2c000000.pcie: MEM 0x0980000000..0x09bfffffff -> 0x0980000000 [ 1.353853] ATR entry: 0x09c0000000 -> 0x0000000000 [0x0010000000] (param: 0x000001) [ 1.353885] ATR entry: 0x0038000000 -> 0x0038000000 [0x0008000000] (param: 0x000000) [ 1.353915] ATR entry: 0x0980000000 -> 0x0980000000 [0x0040000000] (param: 0x000000) [ 1.772913] pcie_plda 2c000000.pcie: Port link down, exit. [ 1.786860] clk-starfive-jh7110-vout 295c0000.clock-controller: starfive JH7110 clk_vout init successfully. [ 1.798927] clk-starfive-jh7110-isp 19810000.clock-controller: starfive JH7110 clk_isp init successfully. [ 1.799658] dw_axi_dmac_platform 16050000.dma-controller: DesignWare AXI DMA Controller, 4 channels [ 1.800750] printk: console [ttyS0] disabled [ 1.821002] 10000000.serial: ttyS0 at MMIO 0x10000000 (irq = 17, base_baud = 1500000) is a 16550A [ 3.396811] printk: console [ttyS0] enabled [ 3.403021] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller [ 3.408541] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 1 [ 3.416537] xhci-hcd xhci-hcd.1.auto: hcc params 0x200073c8 hci version 0x100 quirks 0x0000002000018010 [ 3.426005] xhci-hcd xhci-hcd.1.auto: irq 53, io mem 0x10110000 [ 3.432171] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller [ 3.437698] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 2 [ 3.445397] xhci-hcd xhci-hcd.1.auto: Host supports USB 3.0 SuperSpeed [ 3.452780] hub 1-0:1.0: USB hub found [ 3.456580] hub 1-0:1.0: 1 port detected [ 3.461009] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM. [ 3.469811] hub 2-0:1.0: USB hub found [ 3.473638] hub 2-0:1.0: 1 port detected [ 3.478149] cdns3-starfive 10210000.usbdrd: usb mode 1 3.0 probe success [ 3.485116] jh7110-vin 19800000.vin_sysctl: stfcamss probe enter! [ 3.494714] jh7110-vin 19800000.vin_sysctl: stfcamss probe success! [ 3.513255] dwmmc_starfive 16010000.sdio0: IDMAC supports 32-bit address mode. [ 3.514837] dwmmc_starfive 16020000.sdio1: IDMAC supports 32-bit address mode. [ 3.520607] dwmmc_starfive 16010000.sdio0: Using internal DMA controller. [ 3.527918] dwmmc_starfive 16020000.sdio1: Using internal DMA controller. [ 3.534697] dwmmc_starfive 16010000.sdio0: Version ID is 290a [ 3.541515] dwmmc_starfive 16020000.sdio1: Version ID is 290a [ 3.547382] dwmmc_starfive 16010000.sdio0: DW MMC controller at irq 29,32 bit host data width,32 deep fifo [ 3.553204] dwmmc_starfive 16020000.sdio1: DW MMC controller at irq 30,32 bit host data width,32 deep fifo [ 3.563216] mmc_host mmc0: card is non-removable. [ 3.572947] mmc_host mmc1: card is polling. [ 3.582562] jh7110-sec 16000000.crypto: will run requests pump with realtime priority [ 3.595302] jh7110-sec 16000000.crypto: Initialized [ 3.600878] starfive-i2s 120b0000.i2stx_4ch0: designware: play supported [ 3.607677] starfive-i2s 120b0000.i2stx_4ch0: designware: i2s master mode supported [ 3.615643] sf-mipi-dphy-tx 295e0000.mipi-dphy: sf_dphy_probe begin [ 3.621910] sf-mipi-dphy-tx 295e0000.mipi-dphy: ===> sf_dphy_probe enter, 445 [ 3.629213] sf-mipi-dphy-tx 295e0000.mipi-dphy: control ECO [ 3.634802] sf-mipi-dphy-tx 295e0000.mipi-dphy: supply mipi_1p8 not found, using dummy regulator [ 3.643781] sf-mipi-dphy-tx 295e0000.mipi-dphy: sf_dphy_probe end [ 3.649985] cdns-dsi 295d0000.mipi: dsi_sys_clk = 297000000 [ 3.655726] cdns-dsi 295d0000.mipi: starfive dsi bind end [ 3.662588] of_cfs_init [ 3.665111] of_cfs_init: OK [ 3.668237] starfive-pwmdac 100b0000.pwmdac: clk_apb0 = 49500000, clk_pwmdac_apb = 49500000, clk_pwmdac_core = 4068493 [ 3.679601] cfg80211: Loading compiled-in X.509 certificates for regulatory database [ 3.742691] usb 1-1: new high-speed USB device number 2 using xhci-hcd [ 3.792704] mmc_host mmc0: Bus speed (slot 0) = 198000000Hz (slot req 400000Hz, actual 399193HZ div = 248) [ 3.792705] mmc_host mmc1: Bus speed (slot 0) = 198000000Hz (slot req 400000Hz, actual 399193HZ div = 248) [ 3.804983] cfg80211: Loaded X.509 cert 'sforshee: 00b28ddf47aef9cea7' [ 3.818967] platform regulatory.0: Direct firmware load for regulatory.db failed with error -2 [ 3.827636] cfg80211: failed to load regulatory.db [ 3.924746] hub 1-1:1.0: USB hub found [ 3.928626] hub 1-1:1.0: 4 ports detected [ 4.032211] starfive soc:display-subsystem: bound 29400000.dc8200 (ops 0xffffffff81077ec0) [ 4.040619] innohdmi-starfive 29590000.hdmi: inno hdmi bind begin [ 4.048166] innohdmi-starfive 29590000.hdmi: [drm:inno_hdmi_bind] registered Inno HDMI I2C bus driver success [ 4.058262] innohdmi-starfive 29590000.hdmi: HDMI&AUDIO register done. [ 4.064818] innohdmi-starfive 29590000.hdmi: inno hdmi bind end [ 4.070736] starfive soc:display-subsystem: bound 29590000.hdmi (ops 0xffffffff81078c58) [ 4.078843] vs-simple-encoder soc:dsi-output: encoder_bind begin [ 4.084882] no panel, -517 [ 4.087591] vs-simple-encoder soc:dsi-output: encoder_bind error [ 4.093606] starfive soc:display-subsystem: bound soc:dsi-output (ops 0xffffffff810788a0) [ 4.102278] [drm] Initialized starfive 1.0.0 20191101 for soc:display-subsystem on minor 0 [ 4.110632] starfive soc:display-subsystem: [drm] Cannot find any crtc or sizes [ 4.118129] starfive soc:display-subsystem: [drm] Cannot find any crtc or sizes [ 4.125470] starfive soc:display-subsystem: [drm] Cannot find any crtc or sizes [ 4.138326] mmc_host mmc1: Bus speed (slot 0) = 198000000Hz (slot req 50000000Hz, actual 49500000HZ div = 2) [ 4.148290] mmc1: new high speed SDHC card at address b368 [ 4.155002] mmcblk1: mmc1:b368 NCard 7.48 GiB [ 4.171452] mmcblk1: p1 [ 4.252813] mmc_host mmc0: Bus speed (slot 0) = 198000000Hz (slot req 300000Hz, actual 300000HZ div = 330) [ 4.362758] usb 1-1.1: new high-speed USB device number 3 using xhci-hcd [ 4.594816] hub 1-1.1:1.0: USB hub found [ 4.598885] hub 1-1.1:1.0: 4 ports detected [ 4.692718] mmc_host mmc0: Bus speed (slot 0) = 198000000Hz (slot req 200000Hz, actual 200000HZ div = 495) [ 4.802772] usb 1-1.2: new high-speed USB device number 4 using xhci-hcd [ 5.142742] mmc_host mmc0: Bus speed (slot 0) = 198000000Hz (slot req 100000Hz, actual 100000HZ div = 990) [ 5.232699] usb 1-1.1.2: new low-speed USB device number 5 using xhci-hcd [ 5.455834] eric-tx CALL alloc_txring !!!! [ 5.475694] input: DELL DELL USB Keyboard as /devices/platform/soc/10210000.usbdrd/10100000.usb/xhci-hcd.1.auto/usb1/1-1/1-1.1/1-1.1.2/1-1.1.2:1.0/0003:413C:2005.0001/input/input0 [ 5.552948] hid-generic 0003:413C:2005.0001: input: USB HID v1.10 Keyboard [DELL DELL USB Keyboard] on usb-xhci-hcd.1.auto-1.1.2/input0 [ 6.132699] ALSA device list: [ 6.135681] #0: Starfive-PWMDAC-Sound-Card [ 6.139959] #1: Starfive-HDMI-Sound-Card [ 6.148184] Freeing unused kernel image (initmem) memory: 2188K [ 6.154366] Run /init as init process [ 15.619542] EXT4-fs (mmcblk1p1): mounted filesystem with writeback data mode. Opts: data=writeback. Quota mode: disabled. [ 16.567925] systemd[1]: System time before build time, advancing clock. [ 16.623134] systemd[1]: systemd 252.6-1 running in system mode (+PAM +AUDIT +SELINUX +APPARMOR +IMA +SMACK +SECCOMP +GCRYPT -GNUTLS +OPENSSL +ACL +BLKID +CURL +ELFUTILS +FIDO2 +IDN2 -IDN +IPTC +KMOD +LIBCRYPTSETUP +LIBFDISK +PCRE2 -PWQUALITY +P11KIT +QRENCODE +TPM2 +BZIP2 +LZ4 +XZ +ZLIB +ZSTD -BPF_FRAMEWORK -XKBCOMMON +UTMP +SYSVINIT default-hierarchy=unified) [ 16.655158] systemd[1]: Detected architecture riscv64. [ 16.670100] systemd[1]: Hostname set to . [ 17.161083] (sd-execut[229]: /usr/lib/systemd/system-generators/netplan failed with exit status 1. [ 17.768625] systemd[1]: Queued start job for default target graphical.target. [ 17.778993] systemd[1]: Created slice system-getty.slice - Slice /system/getty. [ 17.787360] systemd[1]: Created slice system-modprobe.slice - Slice /system/modprobe. [ 17.796047] systemd[1]: Created slice system-serial\x2dgetty.slice - Slice /system/serial-getty. [ 17.805354] systemd[1]: Created slice user.slice - User and Session Slice. [ 17.812391] systemd[1]: bootsplash-ask-password-console.path - Dispatch Password Requests to Console Directory Watch when bootsplash is active was skipped because of an unmet condition check (ConditionPathExists=/sys/devices/platform/bootsplash.0/enabled). [ 17.835272] systemd[1]: Started systemd-ask-password-wall.path - Forward Password Requests to Wall Directory Watch. [ 17.846010] systemd[1]: proc-sys-fs-binfmt_misc.automount - Arbitrary Executable File Formats File System Automount Point was skipped because of an unmet condition check (ConditionPathExists=/proc/sys/fs/binfmt_misc). [ 17.865479] systemd[1]: Reached target cryptsetup.target - Local Encrypted Volumes. [ 17.873380] systemd[1]: Reached target integritysetup.target - Local Integrity Protected Volumes. [ 17.882545] systemd[1]: Reached target paths.target - Path Units. [ 17.888939] systemd[1]: Reached target slices.target - Slice Units. [ 17.895436] systemd[1]: Reached target swap.target - Swaps. [ 17.901175] systemd[1]: Reached target time-set.target - System Time Set. [ 17.908247] systemd[1]: Reached target veritysetup.target - Local Verity Protected Volumes. [ 17.924192] systemd[1]: Listening on rpcbind.socket - RPCbind Server Activation Socket. [ 17.932804] systemd[1]: Listening on syslog.socket - Syslog Socket. [ 17.939494] systemd[1]: Listening on systemd-fsckd.socket - fsck to fsckd communication Socket. [ 17.948471] systemd[1]: Listening on systemd-initctl.socket - initctl Compatibility Named Pipe. [ 17.964040] systemd[1]: systemd-journald-audit.socket - Journal Audit Socket was skipped because of an unmet condition check (ConditionSecurity=audit). [ 17.978119] systemd[1]: Listening on systemd-journald-dev-log.socket - Journal Socket (/dev/log). [ 17.987621] systemd[1]: Listening on systemd-journald.socket - Journal Socket. [ 17.995260] systemd[1]: systemd-networkd.socket: Socket service systemd-networkd.service not loaded, refusing. [ 18.005320] systemd[1]: Failed to listen on systemd-networkd.socket - Network Service Netlink Socket. [ 18.016013] systemd[1]: Listening on systemd-udevd-control.socket - udev Control Socket. [ 18.024532] systemd[1]: Listening on systemd-udevd-kernel.socket - udev Kernel Socket. [ 18.034439] systemd[1]: Mounting dev-hugepages.mount - Huge Pages File System... [ 18.043791] systemd[1]: Mounting dev-mqueue.mount - POSIX Message Queue File System... [ 18.053907] systemd[1]: Mounting sys-kernel-debug.mount - Kernel Debug File System... [ 18.062228] systemd[1]: sys-kernel-tracing.mount - Kernel Trace File System was skipped because of an unmet condition check (ConditionPathExists=/sys/kernel/tracing). [ 18.077666] systemd[1]: auth-rpcgss-module.service - Kernel Module supporting RPCSEC_GSS was skipped because of an unmet condition check (ConditionPathExists=/etc/krb5.keytab). [ 18.096999] systemd[1]: Starting fake-hwclock.service - Restore / save the current clock... [ 18.107899] systemd[1]: Starting ifupdown-wait-online.service - Wait for network to be configured by ifupdown... [ 18.120712] systemd[1]: Starting keyboard-setup.service - Set the console keyboard layout... [ 18.132070] systemd[1]: Starting kmod-static-nodes.service - Create List of Static Device Nodes... [ 18.144154] systemd[1]: Starting modprobe@configfs.service - Load Kernel Module configfs... [ 18.155506] systemd[1]: Starting modprobe@dm_mod.service - Load Kernel Module dm_mod... [ 18.166635] systemd[1]: Starting modprobe@drm.service - Load Kernel Module drm... [ 18.177246] systemd[1]: Starting modprobe@efi_pstore.service - Load Kernel Module efi_pstore... [ 18.188990] systemd[1]: Starting modprobe@fuse.service - Load Kernel Module fuse... [ 18.200247] systemd[1]: Starting modprobe@loop.service - Load Kernel Module loop... [ 18.210059] systemd[1]: systemd-fsck-root.service - File System Check on Root Device was skipped because of an unmet condition check (ConditionPathExists=!/run/initramfs/fsck-root). [ 18.231858] systemd[1]: Starting systemd-modules-load.service - Load Kernel Modules... [ 18.242221] systemd[1]: Starting systemd-network-generator.service - Generate network units from Kernel command line... [ 18.256136] systemd[1]: Starting systemd-remount-fs.service - Remount Root and Kernel File Systems... [ 18.268554] systemd[1]: Starting systemd-udev-trigger.service - Coldplug All udev Devices... [ 18.283430] systemd[1]: Mounted dev-hugepages.mount - Huge Pages File System. [ 18.288067] EXT4-fs (mmcblk1p1): re-mounted. Opts: commit=600,errors=remount-ro. Quota mode: disabled. [ 18.302828] systemd[1]: Mounted dev-mqueue.mount - POSIX Message Queue File System. [ 18.311218] systemd[1]: Mounted sys-kernel-debug.mount - Kernel Debug File System. [ 18.319580] systemd[1]: Finished fake-hwclock.service - Restore / save the current clock. [ 18.335607] systemd[1]: Finished ifupdown-wait-online.service - Wait for network to be configured by ifupdown. [ 18.346572] systemd[1]: Finished kmod-static-nodes.service - Create List of Static Device Nodes. [ 18.356439] systemd[1]: modprobe@configfs.service: Deactivated successfully. [ 18.363992] systemd[1]: Finished modprobe@configfs.service - Load Kernel Module configfs. [ 18.373257] systemd[1]: modprobe@dm_mod.service: Deactivated successfully. [ 18.380764] systemd[1]: Finished modprobe@dm_mod.service - Load Kernel Module dm_mod. [ 18.389519] systemd[1]: modprobe@drm.service: Deactivated successfully. [ 18.396583] systemd[1]: Finished modprobe@drm.service - Load Kernel Module drm. [ 18.404931] systemd[1]: modprobe@efi_pstore.service: Deactivated successfully. [ 18.412723] systemd[1]: Finished modprobe@efi_pstore.service - Load Kernel Module efi_pstore. [ 18.422122] systemd[1]: modprobe@fuse.service: Deactivated successfully. [ 18.429289] systemd[1]: Finished modprobe@fuse.service - Load Kernel Module fuse. [ 18.437640] systemd[1]: modprobe@loop.service: Deactivated successfully. [ 18.444898] systemd[1]: Finished modprobe@loop.service - Load Kernel Module loop. [ 18.453142] systemd[1]: Finished systemd-modules-load.service - Load Kernel Modules. [ 18.461599] systemd[1]: Finished systemd-network-generator.service - Generate network units from Kernel command line. [ 18.473126] systemd[1]: Finished systemd-remount-fs.service - Remount Root and Kernel File Systems. [ 18.483298] systemd[1]: Reached target network-pre.target - Preparation for Network. [ 18.493357] systemd[1]: Mounting sys-fs-fuse-connections.mount - FUSE Control File System... [ 18.504767] systemd[1]: Mounting sys-kernel-config.mount - Kernel Configuration File System... [ 18.513998] systemd[1]: systemd-pstore.service - Platform Persistent Storage Archival was skipped because of an unmet condition check (ConditionDirectoryNotEmpty=/sys/fs/pstore). [ 18.532372] systemd[1]: Starting systemd-random-seed.service - Load/Save Random Seed... [ 18.541021] systemd[1]: systemd-repart.service - Repartition Root Disk was skipped because no trigger condition checks were met. [ 18.555302] systemd[1]: Starting systemd-sysctl.service - Apply Kernel Variables... [ 18.566378] systemd[1]: Starting systemd-sysusers.service - Create System Users... [ 18.581739] systemd[1]: Finished keyboard-setup.service - Set the console keyboard layout. [ 18.590867] systemd[1]: Mounted sys-fs-fuse-connections.mount - FUSE Control File System. [ 18.599729] systemd[1]: Mounted sys-kernel-config.mount - Kernel Configuration File System. Armbian 23.5.0-trunk.231 Sid hvc0 star64 login: